THUNDER LASER’s Odin Laser Engraving Machine helps you bring your concepts and ideas into highly-detailed and actual 3D engraving on any material.

The machine features a Japanese Oriental motor that brings 5G acceleration to reach an engraving speed of up to 2000mm/s. Partnered with our self-designed smooth guide rail, you’ve guaranteed a consistent 3D engraving effect no matter the pattern. It’s built-in RF tube increases the engraving resolution up to 1000 DPI.

Laser Type: RF CO2

Work Area : 559×381 up to 813x508mm

Laser Power: 30w,55w

Z-axis: 185mm

Features

New: 100% faster motor system

The Odin series laser engraver is with high speed and high resolution motor system imported from Japanese ORIENTAL.

The 5-phase open-loop stepper motor for X-axis offers balanced performance enhanced by high torque, low vibration
and low noise, it turns out to be high efficiency with 3G acceleration and 80IPS speed, providing a super-fast engraving in the industry.

Different from X-axis motor, Y axis motor is a higher resolution type of the same series.

This Y-axis motor takes only quarter degree per step than X-axis, with 7 times Accuracy than Nova motor.

New: 100% smoother guide Rail

This new guide Rail was new developed by Thunder Laser engineers with patent right.

It matches the new Oriental motor system very well. Less resistance and low noise,that’s the most important factor why Odin series could reach 2000mm/s speed.

RF Laser Tube

The RF metal lasers are designed to operate without high voltage or water cooling. This makes RF metal lasers inherently safer to operate in almost any environment.

RF metal lasers are designed to be durable, provide the highest performance with high laser beam quality, offer indefinite service life, and help assure operator safety.

The price is more expensive than DC glass tube, but they have a longer lifespan of up to approximately 10,000hours.

New: Upper & Lower Vent

New feature for Odin series with Upper and Lower exhaust ventilations design, to remove the heated and burned smoke from the material surface timely while engraving and cutting.

Dual Air-Assist System

Accurate control of your air assist for cutting and engraving. High and low air pressures allow for cleaner result.

Controlled by the smart board, there are 2 modes for Thunder Laser machine’s air assist feature. Usually we set Low volumn air for engrave and High volumn air for cut on the design drawing layer on laser software, so as to get cleaner results on both engraving and cutting process.

This also works on Lightburn software. For cutting, just toggle air assist ON; for engraving, toggle air assist OFF and it will activate the low air stage.

Air assist is an important feature to lower the risk of meterials’ catching fire when being heated by laser. Also air assist prevents the lens from the smoke and dust generated during laser processing on materials.

Neither the Low volume air or high volumn air will be activated until the laser starts. So this proprietary Dual air function also helps on energy conservation and noise

New: Eightfold Open-flap protection

8 x Open-cover protection sensor switches were installed on four covers, there are 2pcs in the back of the machine where to install the laser source, 2pcs in the left cover of the machine, 2pcs in the front cover, and 2pcs on the top cover.

Dual Open-cover protection for each cover is the standard for CE certification and FDA requirement. It makes sure the whole machine is safe enough for operator. Should any of the sensors fail, the protection would still work.

To make the machine maintenance easier, our engineers developed a patent circuit board to detect those sensors’ working state, and there is one button to switch to maintenance mode for laser beam aligning.

We Put Safety First

Gain more confidence in using our Odin laser engraving machines with their vast array of safety features to protect users during operation.

Our machines are built with basic security devices, including an emergency stop, alarm lamp, earth wiring, and breakers.

Additionally, we’ve added CE and FDA-approved 8x open flap protection windows with sensors on each one for proper monitoring. These windows are made of high-grade acrylic material, meaning that the laser won’t penetrate and secure the machine operator. Also, heat detector alarms are equipped to detect any abnormal equipment activity, like overheating and fire.

Creating More Possibilities

Thunder Laser helps you push your imagination through the constant innovation we deliver in our Odin Laser Engraving machine. Adjustable laser power and the proprietary dual air-assist system open doors for design customization and make different layers on the material, leading to more intricate designs.